關於我們 產品目錄 視頻   消息 方案解決 常見問題 產品技術 服務保修 用戶服務 聯繫我們
觸摸屏技術
自訂頁
2點觸摸屏技術
多點觸摸技術
拼接牆
觸摸膜技術
電子白板技術
自訂頁

觸摸屏技術 

4Wire Resistive Touch Screen Working Principle:

The 4 Wire Resistive Touch Screen is a two-layer structure,
1. ITO glass substrate with one side uniform resistive ITO coating.
2. A very thick polyester ITO film which tightly suspended over the top of ITO glass substrate. This PET film has a hard, durable coating on the outer side, on inner side with ITO coating.
3. ITO glass and the ITO film are separated by printed small, transparent insulation spacer dots.
When the screen is touched, it pushes the ITO film to have an electrical contact with ITO glass (both on the ITO coating side). It produces a voltage which is the analog representation of the position touched.

 In 4 Wire Resistive, the ITO glass (glass substrate) is set as Y axis, and ITO film as X axis. The microprocessor of controller applies +5V voltage to XL (X axis left) on the ITO film, and the voltage uniformly decreases to XR(X axis right) in zero voltage. In the same process, the microprocessor applies +5V voltage to YU (Y axis up) on the ITO glass, and the voltage uniformly decreases to YD (Y axis down) in zero voltage. When the screen is not touched, the controller detects the voltage on ITO glass / ITO film as zero voltage.

 When the screen is touched, the voltage on the ITO film proportional to the X axis (horizontal) position of the touch point appears on the ITO glass. Next, the voltage on the ITO glass proportional to the Y axis (vertical) position of the touch point appears on the ITO film. These two voltages appearing on the ITO film and ITO glass are digitized by the A/D converter and then transmitted to the host.

 The controller will receive all data to get the touched position according to the established calculating mode to figure out the exact X and Y coordinates


Advantages
  • Can be activated with any device
  • Low cost solution
  • Low power consumption
  • Disadvantages
  • Less durability compared to other technologies
  • Less transmittance and overall optical quality
  • Requires periodic recalibration
     

5 Wire Resistive Touch Screen Working Principle:
The 5 Wire Resistive Touch Screen is a two layer structure,
1.ITO glass substrate with one side uniform resistive ITO coating.
2. A very thick polyester ITO film is tightly suspended over the top of ITO glass substrate. This ITO film has a hard, durable coating on the outer side, on an inner side with ITO coating.
3.The ITO glass and the ITO film is separated by printed small, transparent insulation spacer dots.

When the screen is touched, it pushes the ITO film to have an electrical contact with ITO glass (both on the ITO coating side). It then produces a voltage which is the analog representation of the position touched.

 The 5 wire touch screen controller is always ready for a touch, and the resistive layer of touch screen is biased at +5V through 4 drive lines on the glass (ITO coating side) and the ITO film is grounded through a high resistance. When there is no touch on the screen, the voltage is zero on the ITO film. The voltage level of the ITO film is analog - to - digital converter (A/D converter) and monitored by the microprocessor on the controller.

   When the screen is touched, the microprocessor detects the voltage rise in the ITO film and begins to convert the coordinates. The microprocessor places the X drive voltage by applying +5V voltage to pins H, X and grounding pins Y and L. The analog voltage is proportional to the X position (horizontal) of the touch point and appears on the ITO film at pin S of the touch screen tail's connector. This voltage is digitized by the A/D converter and transmitted to the computer.  

 In same process, the microprocessor places the Y drive voltage by the same +5V to pins H, Y and ground pins X and L. The analog voltage is proportional to the Y position (vertical) of touch point and appears on the ITO film at pin S of the touch screen tail's connector. The signal is converted and processed same as for the X position.

 The controller will receive all data to calculate the touched position according to pre-established modes for the exact X and Y coordinates.

Advantages

  • Can be activated with any device
  • Low cost solution
  • Low power consumption
  • Disadvantages
  • Less durability compared to other technologies
  • Less transmittance and overall optical quality
  • Requires periodic recalibration
Applications:
  • 5 Wire Resistive touch screen is with the most extensive applications.
  • Point-of-Sale uses: convenience store, movie theater, lottery terminal, fast food, etc.
  • Industrial uses: Automated testing, automation equipment, man。machine interface, etc.
  • Medical uses: medical instrument, research equipment and patient monitoring system.
  • Transportation uses: Inner vehicle control panel.

Infrared Touch Screen is a touch frame which is usually installed in front of the display screen. The frame is integrated with printed circuit board which contains a line of IR-LEDs and photo transistors hidden behind the bezel of the touch frame. Each of IR-LEDs and photo transistors is set on the opposite sides to create a grid of invisible infrared light. The bezel shields the parts from the operation environment while allowing the IR beams to pass through.

 The Infrared Touch Screen controller sequentially pulses LEDs to create a grid of IR light beams. When a user touches the screen, enters the grid by a stylus which can interrupt the IR light beams, the photo transistors from X and Y axes detect the IR light beams which have been interrupted and transmit exact signals that identify the X and Y axes coordinates to the host.

SAW Touch Screen working principle:
SAW Touch Screen parts include: Sensor / Control Card / Cables. There are 4 transducers attached to the beveled edges of the glass for both X and Y axes
( 2 for transmitting and 2 for receiving).

The control card sends electrical signals to transmitting transducers of both X and Y axes. The transducers convert these electrical signals from the control card into ultrasonic waves sent to the array of reflectors on the glass surface, and the acoustic waves are directed across to the front surface of the glass by the array of reflectors (the degree of the array of reflectors depends on the updating design). The opposite reflectors will gather and direct waves to the receiving transducers which will convert the waves into the electrical signals.

 When a user touches the screen, the touch point coordinate is calculated by the control card comparing the received average amplitude of vibration of the acoustic wave signals and reference average waveform acquired when the touchscreen is in an untouched condition. The controller is capable of detecting the stay time of dirt, dust, water drops, scratches and other contaminants on the screen and then ignores them. If the contamination is removed, the controller relearns the original reference average waveform.

Advantages

  • Very high transmittance
  • Very high durability

Disadvantages

  • Cannot be sealed
  • Requires “soft” input device
  • Surface obstructions can cause a false touch
     

Public access Application

  • Point-of-information kiosks
  • Gaming, lottery, and amusement
  • Vending and ticket sales
  • Public pay phones
  • Multimedia marketing
  • Banking / financial transactions
     


Powered by DIYTrade.com
網站首頁聯繫我們網站地圖